Shaping Average / Peak vs. Policing
Chris,
so did devel guys tell you anything on shape peak? 
As to my tests it always shapes up to “target” rate, i.e. with shape peak 64000 we get limit of 128000
I actually was unable to run iperf, and did all the measurements with ping/load-interval/show int. Platform 3640, IOS 12.3(14)T.
2006/7/5, Chris Lewis : > > Shape average does not allow Bc + Be to be sent every interval. > > Shape average allows Be to be sent in addition to Bc on the first interval > of a second only, also the shaper needs to have built up credit in > previous > intervals to use Be. The effect of Be in shape average is to allow the > shaper to achieve CIR over a long period of time, accommodating periods of > lull where less than CIR is sent in one second, with an additional Be > amount > of data in a later period should the credit be available and the shaper > needing to send more data. > > Chris > > > On 7/4/06, Joe Gagznos wrote: > > > > I am trying to find another way to limit outbound traffic through an > > interface similar in manner to policing. I understand that functionally > > the > > two are different. With shaping you are going to be queuing excess > > traffic > > to a predetermined rate where with policing you are going to be > executing > > some kind of action on traffic that exceeds the contract (usually > > dropping). > > > > For comparison purposes, I have configured shaping and policing on two > > separate subinterfaces in the following manner: > > > > interface Ethernet0/0.1 > > encapsulation dot1Q 10 > > ip address 10.1.1.1 255.255.255.0 > > service-policy output shape > > > > interface Ethernet0/0.2 > > encapsulation dot1Q 20 > > ip address 10.1.2.1 255.255.255.0 > > service-policy output police > > > > Both interfaces are configured to limit traffic to no more than 2.5 Mbps > > as > > follows: > > > > policy-map police > > class class-default > > police 2500000 conform-action transmit exceed-action drop > > > > policy-map shape > > class class-default > > shape average 2500000 > > > > What I find is that the shaping interface initializes the parameters as > > follows: > > > > R1#sh policy-map interface e0/0.1 > > Ethernet0/0.1 > > > > Service-policy output: shape > > > > Class-map: class-default (match-any) > > 19 packets, 1729 bytes > > 5 minute offered rate 0 bps, drop rate 0 bps > > Match: any > > Traffic Shaping > > Target/Average Byte Sustain > > Excess Interval Increment > > Rate Limit bits/int bits/int > (ms) > > (bytes) > > 2500000/2500000 15000 60000 60000 24 7500 > > > > Adapt Queue Packets Bytes Packets Bytes Shaping > > Active Depth Delayed Delayed Active > > - 0 19 1729 0 0 no > > > > A couple things to note here - Be is initialized to the same value as Bc > > of > > 60000 (or 7500 bytes). The byte limit is 15000 bytes, though. This > must > > mean that the byte limit is initialized to Bc+Be=15000. With a 24 ms > > interval, does this mean that the interface will send 5 Mbps (15000 * 8 > > bits > > / byte * 1 sec/.024 = 5000000) instead of the contracted 2.5 Mbps? If > > shape average is allowing the interface to transmit Bc+Be each interval, > > then how does this differ from configuring shape peak which accomplishes > > the > > same thing? > > > > With policing it appears that things are much more straightforward. > > > > R1#sh policy-map int e0/0.2 > > Ethernet0/0.2 > > > > Service-policy output: police > > > > Class-map: class-default (match-any) > > 107 packets, 7473 bytes > > 5 minute offered rate 0 bps, drop rate 0 bps > > Match: any > > police: > > cir 2500000 bps, bc 78125 bytes > > conformed 63 packets, 4305 bytes; actions: > > transmit > > exceeded 0 packets, 0 bytes; actions: > > drop > > conformed 0 bps, exceed 0 bps > > > > Thanks for any response! > > > > Joe Gagznos > > > > _______________________________________________________________________ > > Subscription information may be found at: > > http://www.groupstudy.com/list/CCIELab.html > > _______________________________________________________________________ > Subscription information may be found at: > http://www.groupstudy.com/list/CCIELab.html >
– Petr Lapukhov, CCIE #16379 petr@internetworkexpert.com
Internetwork Expert, Inc. http://www.InternetworkExpert.com Toll Free: 877-224-8987 Outside US: 775-826-4344
Category: CCIE Study
